Five Safety for vernier height guage
Answers
Explanation:
Whenever the vernier height gauge is not used, it should be kept in their cases. In long height gauges, to avoid its heating by warmth from the hands, care should be taken. The springing of the measuring jaw should be always avoided.
Related Questions
Malia is working with aluminum wire. while working with this type of wire, she must remember to a. always use pressure-type terminals. b. avoid copper connectors. c. avoid solder-type lugs. d. apply antioxidation paste
Answers
Answer:
B
Explanation:
Aluminium doesn't rust unless exposed to copper for a duration of time.
Suppose that all the dislocations in 3000 mm3 of crystal were somehow removed and linked end to end. Given 1 m =0.0006214 mile, how far (in miles) would this chain extend for dislocation densities of (a) 10^4 mm^-2 (undeformed metal)? (b) 10^10 mm-2 (cold-worked metal)?
Answers
Answer:
please let me know the answer to this because I need to know as well. thanks
How long does it take for a voltage-gated potassium channel to open? Choose the correct option. A) Voltage-gated potassium channels take about 3 msec to open after depolarization. B) Voltage-gated potassium channels open as soon as the membrane is depolarized beyond threshold. C) Voltage-gated potassium channels do not open immediately upon depolarization; they take about 1 msec to open after the membrane is depolarized. D) Voltage-gated potassium channels open when action potential fire at maximal frequency.
Answers
When the membrane is depolarized, voltage-gated potassium channels do not open instantly; instead, they require roughly 1 msec to open.
How rapidly do voltage-gated potassium channels open?The opening of a group of voltage-gated potassium channels lets potassium stream out of the cell via its electrochemical gradient. These occurrences swiftly reduce the membrane potential, returning it to its typical resting state.
The voltage-gated potassium channel opening mechanism?Depolarization triggers the activation of voltage-gated potassium channels, and the outward flow of potassium ions through them repolarizes the membrane potential to end action potentials, hyperpolarizes the membrane potential immediately after action potentials, and is essential in establishing the resting membrane potential.
To know more about voltage-gated visit:-
https://brainly.com/question/15583551
#SPJ4
Which three items below should a driver be able to identify under the hood of a car?
Answers
Answer:
Engine oil level.
Brake fluid.
Power steering fluid.
When modeling an engineering process, the right choice between a simple but crude and a complex but accurate model is usually the _______
Answers
When modeling an engineering process, the right choice between a simple but crude and a complex but accurate model is usually the complex model.
What is the engineering process?Engineers frequently follow a set of phases known as the engineering design cycle when developing useful goods, as well as procedures. This design are being frequently used by the person to create a model through which it can do various structural inputs.
The purpose of this modeling is to solve the complexity of the model as well as to allow a tolerable that can be more reliable.A complicated though the precise model is typically preferable to a simple yet unsophisticated one when simulating an engineering process.
Learn more about the engineering process, here:
https://brainly.com/question/10175918
#SPJ1
I need to solve for d
Answers
Answer:
it's not included
Explanation:
plz exact ur explain
Answer:
si amor
Explanation:
Hoiykñjdnlklbutrk
All of the following statements are true with respect to testing the air-conditioning
system EXCEPT:
The heater fan needs to be on the lowest speed.
The heater control knob should be on the coldest setting.
The airflow should be set to the dash vents.
An external fan should be used to supply air to the condenser to simulate driving
conditions.
Answers
An external fan should be used to supply air to the condenser to simulate driving conditions is not true statement.
How do you test an air conditioner?Turn on the AC unit, leave a thermometer on the supply register for five minutes, then check the temperature and contrast it with the temperature coming from the return vent to test your central air conditioning system.To avoid overworking or harming the compressor of the system, an Air conditioner test is best performed a few days after the external temperature has stayed above 65 degrees Fahrenheit and under no circumstances lower than 60 degrees.If the temperature is below 65 degrees Fahrenheit, HVAC manufacturers typically advise consumers not to operate their units for extended periods of time. Wait at least three days after the temperature has been over 60 degrees Fahrenheit before testing your appliance.Learn more about Air conditioner test refer to :
https://brainly.com/question/30140375
#SPJ1
A 5 MHz clock that generates a 0 to 5V pulse train with a 30% duty cycle is connected to input X of a two input OR gate that has a 20nS propagation delay. The clock also goes to an inverter with a 10ns propagation delay. The output of the inverter goes to the Y input of the OR gate.
a. Draw the circuit
b. Plot the output of the clock for two cycles. Show times and voltages.
c. Plot the output of the inverter in the same plot. Show times and voltages.
d. Plot the output of the OR gate in the same plot. Show times and voltages.
Answers
Answer:
Timing Diagrams 15 pts. A 10 MHz clock that generates a 0 to 5V pulse train with a 30% duty cycle is connected to input X of a two input OR gate that has a 20nS propagation delay. The clock also goes to an inverter with a 10 ns propagation delay. The output of the inverter goes to the Y input of the OR gate. a) Draw the circuit. 2 pts. b) Plot the output of the clock for two cycles. Show times and voltages. 5 pts. c) On the same page as part (b) plot the output of the inverter. Show times and voltages. 3 pts. d) On the same page as parts (b & c) plot the output of the OR gate. Show times and voltages. 5 pts.
What type of caliper is shown here?
Answers
Answer:
its a floating caliper definetly
tech a says that the transmission in a toyota hybrid has a separate gear to provide reverse. tech b says that toyota hybrids use a variable diameter pulley (vdp) type continuously variable transmission (cvt). who is correct?
Answers
Answer:
Tech B is correct. Toyota hybrids use a continuously variable transmission (CVT) with a variable diameter pulley (VDP) to provide an infinite number of gear ratios, which eliminates the need for a separate reverse gear.
scrapers are used to haul dirt from a borrow pit to the cap of a landfill. the estimated cycle time for the scrapers is 9.5 minutes. The scrapers carry 10 cubic yards of soil per trip . using a system efficiency of 45 minutes per hour and producitivity factor of determine the number of labor hours to haul 1 cubic yard of dirt. each scraper require one operator
Answers
i gave 15 min to finish this java program
Answers
Answer:
class TriangleNumbers
{
public static void main (String[] args)
{
for (int number = 1; number <= 10; ++number) {
int sum = 1;
System.out.print("1");
for (int summed = 2; summed <= number; ++summed) {
sum += summed;
System.out.print(" + " + Integer.toString(summed));
}
System.out.print(" = " + Integer.toString(sum) + '\n');
}
}
}
Explanation:
We need to run the code for each of the 10 lines. Each time we sum numbers from 1 to n. We start with 1, then add numbers from 2 to n (and print the operation). At the end, we always print the equals sign, the sum and a newline character.
the engine needs a free flow of clean air to operate correctly and with low emissions. True or False
Answers
Answer:
true
Explanation:
while performing a running compression test how should running compression compare to static compression
Answers
Answer:
The idle speed of a running compression should be between 50-75 PSI and that is about half of the static compression.
Explanation:
The Running or Dynamic compression is used to determine how well the cylinder in an engine is absorbing air, reserving it for the proper length of time, and releasing it to the exhaust. The static or cranking compression test is used to check the sealing of the cylinder. Before performing the running compression test, the static compression test is first performed to rule out other issues like bent valves.
The standard value for the static compression is given by;
Compression ratio * 14.7 = Manufacturers Specification
The running compression should always be half of the static compression.
In the production of shafts, it is assumed that the diameters of the shafts produced are
normally distributed, with mean-50 (mm) and variance -8 (mm) 2. What is the probability
that the diameter of a shaft will be at least 48 mm?
Answers
In the production of shafts, the diameters are assumed to be normally distributed with a mean (µ) of 50 mm and a variance (σ^2) of 8 mm². To find the probability that the diameter of a shaft will be at least 48 mm, we will need to use the standard normal distribution (Z-score) formula:
Z = (X - µ) / σ
where X is the value we want to find the probability for (48 mm in this case), µ is the mean, and σ is the standard deviation (square root of the variance, which is √8 ≈ 2.83).
Z = (48 - 50) / 2.83 ≈ -0.71
Now, use a Z-table or a standard normal distribution calculator to find the probability of Z being greater than -0.71. The result should be approximately 0.76 or 76%, meaning there is a 76% probability that the diameter of a shaft will be at least 48 mm.
To know more about production of shafts please check the following link
https://brainly.com/question/13018403
#SPJ11
+ The single bridge rectifierop righas to deliverade current
Of 30A at a dc output Voltage of 100v. if it's supplied by a simple
Phase transformer of ratio 4il.compute the premary and secondary
Voltages and currents. Also calculate the ripple factor for the load
Voltape wave form. Assume the load is highly inductive.
AD2
Eve Ymsinut
load
ADA
DA
93
Answers
Answer:
you are so smart
Explanation:
i have 8 cARS
technician a says that some abs wheel speed sensors are used as part of the tire pressure monitoring system (tpms). technician b says that the abs is used as part of the hill assist system. which technician is correct?
Answers
Technician A said that some ABS wheel speed sensors are used as part of TPMS and similarly Technician B said that ABS is used as part of the hill assist system. And Both Technician statement is correct.
What does the ABS wheel speed sensor do?
Wheel speed sensors are an essential component of your car's anti-lock braking system (ABS) since they continuously relay data about the speed of the wheels to the ABS controller in addition to monitoring vehicle functions like traction control.
How does hill assist work?
The Hill Assist feature automatically maintains the pressure in the braking system when you let off the brake pedal for a brief period of time to prevent your car from rolling back unintentionally.
A tire pressure monitoring system (TPMS) uses an ABS wheel speed sensor as part of it and also as part of the hill assist system.
Hence, Both Technicians are correct.
To learn more about the TPMS from the given link
https://brainly.com/question/28185546
#SPJ4
Which stages occur during incomplete metamorphosis?
ASAP
A. Adult, larva, and pupa
B. Egg, nymph, and adult
C. Larva, nymph, and egg
D. Pupa, egg, and nymph
NO LINKS PLEASE
Answers
Answer:
The answer is B
Explanation: Hope this helps:)
Two identical bulbs in parallel in a radio create a total resistance of 15 ohms in the circuit. What's the resistance of each of the bulbs A. 10 ohms B. 7.5 ohms C. 45 ohms D. 30 ohms
Answers
Answer
letter B is the answer because 7.5+7.5=15
The resistance of each of the bulbs will be 30 ohms. The correct option is D.
What is resistance?To resist the passage of current, use a resistor. When a resistor is included in a circuit, the amount of current that flows through it drops.
Using ohms as the unit, resistance acts as a gauge to quantify how easily current will flow through a circuit.
When resistance falls, current rises, and when resistance rises, current falls. In order to make sure that current flows in circuits at the proper rate, resistors are crucial.
Here, it is given that:
Total resistance is 15 ohms.
We know that, two identical resistors in parallel have an equivalent resistance half the value of either resistor.
So, the total resistance of 15 ohms have the resistance of each of the bulbs as 30 ohms.
Thus, the correct option is D.
For more details regarding resistance, visit:
https://brainly.com/question/29427458
#SPJ2
consider a copper rod that is 3.14 meters, long, 2 cm in diameter, and has an electrical resistivity of 2x10^-6. if the rod is cut in half what is the electrical resistivity of each piece?
Answers
The electrical resistivity of each piece of the copper rod would remain the same as the original rod, regardless of its size or shape.
The electrical resistivity of a material refers to its ability to resist the flow of electric current through it. In this case, we are given a copper rod that is 3.14 meters long, 2 cm in diameter, and has an electrical resistivity of 2x10⁻⁶.
If the rod is cut in half, the electrical resistivity of each piece remains the same as it is a property of the material and not affected by the shape or size of the object.
Therefore, both pieces of the copper rod would have an electrical resistivity of 2x10⁻⁶. This means that each piece of the copper rod would still have the same resistance to the flow of electrical current as the original rod. This property of materials is important in designing electrical circuits and devices, as it allows us to calculate the resistance of different materials and shapes.
You can learn more about electric current at: brainly.com/question/2264542
#SPJ11
A project ha following time chedule: Activity Time in Week Activity Time in Week 1-2 4 5-7 8 1-3 1 6-8 1 2-4 1 7-8 2 3-4 1 8-9 1 3-5 6 8-10 8 4-9 5 9-10 7 5-6 4 Contruct the network and compute: (1) TE and TL for each event (2) Float for each activity (3) Critical path and it duration
Answers
(1) TE and TL for each event
Event 1: TE=0, TL=0
Event 2: TE=4, TL=4
Event 3: TE=1, TL=5
Event 4: TE=2, TL=6
Event 5: TE=6, TL=12
Event 6: TE=1, TL=2
Event 7: TE=8, TL=16
Event 8: TE=9, TL=17
Event 9: TE=8, TL=18
Event 10: TE=16, TL=23
(2) Float for each activity
Activity 1-2: Float=0
Activity 1-3: Float=3
Activity 2-4: Float=2
Activity 3-4: Float=1
Activity 3-5: Float=0
Activity 4-9: Float=0
Activity 5-6: Float=0
Activity 5-7: Float=0
Activity 6-8: Float=7
Activity 7-8: Float=6
Activity 8-9: Float=5
Activity 8-10: Float=0
Activity 9-10: Float=0
(3) The critical path for this project is: 3-4, 4-9, 5-7, 7-8, 8-10, 9-10, with a total duration of 23 weeks.
THE SOLUTIONTo construct the network and compute the requested information, we first need to create a list of events and activities.From the given schedule, we can identify the following events and activities:Events:1, 2, 3, 4, 5, 6, 7, 8, 9, 10
Activities:1-2: 4 weeks
1-3: 1 week
2-4: 1 week
3-4: 1 week
3-5: 6 weeks
4-9: 5 weeks
5-6: 4 weeks
5-7: 8 weeks
6-8: 1 week
7-8: 2 weeks
8-9: 1 week
8-10: 8 weeks
9-10: 7 weeks
Now we can compute the TE (time when an event is expected to start) and TL (time when an event is expected to be completed) for each event, as well as the float (amount of time that an activity can be delayed without delaying the project completion) for each activity.TE and TL for each event:Event 1: TE=0, TL=0
Event 2: TE=4, TL=4
Event 3: TE=1, TL=5
Event 4: TE=2, TL=6
Event 5: TE=6, TL=12
Event 6: TE=1, TL=2
Event 7: TE=8, TL=16
Event 8: TE=9, TL=17
Event 9: TE=8, TL=18
Event 10: TE=16, TL=23
Float for each activity:Activity 1-2: Float=0
Activity 1-3: Float=3
Activity 2-4: Float=2
Activity 3-4: Float=1
Activity 3-5: Float=0
Activity 4-9: Float=0
Activity 5-6: Float=0
Activity 5-7: Float=0
Activity 6-8: Float=7
Activity 7-8: Float=6
Activity 8-9: Float=5
Activity 8-10: Float=0
Activity 9-10: Float=0
The critical path is the sequence of activities that have zero float, meaning they cannot be delayed without delaying the project completion. The critical path for this project is: 3-4, 4-9, 5-7, 7-8, 8-10, 9-10, with a total duration of 23 weeks.Learn more about Construct Network here:
https://brainly.com/question/29355713
#SPJ4
Some ciphers, regardless of type, rely on the difficulty of solving certain mathematical problems, which is the basis for asymmetric key cryptography. Which of the following is a branch of mathematics that involves multiplicative inverses that these ciphers use?A. Factoring small numbersB. Subset sum problemsC. Quantum physicsD. Field theory
Answers
Answer:
D. Field theory.
To think of electric potential difference we are thinking about A. Current B. Voltage C. Resistance
Answers
To think of electric potential difference we are thinking about Voltage. This is option B
The term electric potential difference is used to describe the difference in electric potential between two points in an electrical circuit. The correct answer to the given question is option B, Voltage.
Voltage is the electric potential difference between two points. In other words, voltage is the force that pushes the electric charge through an electrical circuit. The electrical potential difference between two points in an electric circuit is measured in volts, which is abbreviated as V. It is an SI unit of measurement for voltage.
Electric current is the flow of electrons in an electric circuit. It is represented by the symbol I and is measured in amperes (A), which is an SI unit. The current that flows through a circuit is determined by the voltage difference between two points, as well as the resistance of the conductor.
So, the correct answer is B
Learn more about electricity at
https://brainly.com/question/13296426
#SPJ11
1 .8 A capillary tube is immersed vertically in a water container. Knowing that water (3) starts to evaporate when the pressure drops below 2 kPa, determine the maximum capillary rise and tube diameter for this maximum-rise case. Take the contact angle at the inner wall of the tube to be 6 0 and the surface tension to be 1.00 N/m
Answers
The maximum capillary rise and tube diameter for this maximum-rise case will be d=0.414× 10⁻⁴ m.
What do you mean by tube?
A tube, also known as tubing, is a long hollow cylinder that is used to transport fluids (liquids or gases) or to protect electrical and optical cables and wires.
Given that, P = 4 KPa
Contact angle = 6°
Surface tension = 1 N/m
Lets assume that atmospheric pressure = 100 KPa
Lets take that density of water = 1000kg/m³
So the capillarity rise h
h=ΔP/ρg
h= (100×1000-4×1000)/(1000×10)
h= 9.61 m
We know that for capillarity rise h
h=2σcosθ/rρg
r = 2σcosθ/hρg
r = (2×1cos4°)/(9.61×1000×10)
r = 0.207×10⁻⁴m
d=0.414× 10⁻⁴ m
To learn more about tube
https://brainly.com/question/13461230
#SPJ9
The need for extraction of raw metals for making steel has been reduced due to the?
Answers
Answer: Increase in minimills
Explanation:
What does a restriction in the fuel return line cause?
Answers
Answer:
Carburetor flooding, engine stalling, and hard starting
Explanation:
If the fuel return hose becomes blocked or kinked it may cause the carburetor to flood from excessive fuel or pressure buildup.
computer program allowing the computer to communicate with a hardware device called________
Answers
A computer program that enables communication between a computer and a hardware device is known as a device driver. A device driver is a specialized program that allows the operating system to interact with and control the hardware device.
Device drivers play a crucial role in modern computing, as they allow the computer to interact with a wide range of hardware devices, such as printers, scanners, keyboards, mice, and more. Device drivers are typically written by hardware manufacturers and are specific to the hardware device they control. A device driver acts as a translator between the hardware and the operating system, allowing the computer to send and receive data from the hardware device. Without device drivers, hardware devices would not be able to function correctly, and the computer would not be able to use them.
Device drivers are essential for maintaining the compatibility of hardware devices with different operating systems. As technology advances, new hardware devices are developed, and device drivers must be created to allow the computer to interact with them. Device drivers are also updated regularly to fix bugs, improve performance, and add new features. In summary, device drivers are programs that enable communication between a computer and a hardware device. They are essential for the proper functioning of hardware devices and are critical to maintaining compatibility between hardware devices and operating systems.
Learn more about hardware device here-
https://brainly.com/question/26475462
#SPJ11
42. thinning shears with teeth cut more hair than those with teeth. a. longer, less b. less, more c. more, shorter d. more, less
Answers
Shears with teeth cut more hair than ones without teeth, more, less thinning
What is Shear?
Shear is a type of motion or force that causes two parallel surfaces of a material to slide past each other in opposite directions. This motion can be applied to a variety of materials, including metals, plastics, and concrete. When shear is applied to a material, it causes the material to deform in a way that is parallel to the shear direction. This type of motion or force is commonly used in manufacturing, engineering, and construction to shape, cut, or join materials together. Shear can also be used in other applications, such as when studying the behavior of soils or other materials in geotechnical engineering.
To know more about Shear
https://brainly.com/question/20630976
#SPJ4
explain "columnar transposition" for the transposition ciphers using the following plaintext as an example:
abcd
efgh
ijkl
mnop
Answers
Answer:
wa 4tefaw gfawe f
Explanation:
so you do e Fse gaewr gware gfawe agfawe gwar g
Hey guys can anyone list chemical engineering advancement that has been discovered within the past 20 years
Answers
Nanopesticides. The world population keeps growing. ...
Enantio selective organocatalysis. ...
Solid-state batteries. ...
Flow Chemistry. ...
Porous material for Water Harvesting. ...
Directed evolution of selective enzymes. ...
From plastics to monomers. ...