The _____________ must be adhered to for the design and installation of electrical equipment.
a. MUTCD
b. Illumination Engineering Society of North America
c. National Electrical Code
d. Both b) and c)
Answers
The National Electrical Code (NEC) must be adhered to for the design and installation of electrical equipment.
The NEC is a standard that outlines the minimum requirements for safe electrical installations in residential, commercial, and industrial buildings. It is published by the National Fire Protection Association (NFPA) and is updated every three years to reflect the latest advances in electrical technology and safety practices. The NEC covers a wide range of topics, including wiring and grounding, electrical panels and circuits, lighting and power distribution, and electrical safety standards. Adhering to the NEC is essential for ensuring the safe and reliable operation of electrical equipment and minimizing the risk of electrical hazards and fires.
To learn more about Electrical click on the link below:
brainly.com/question/30757813
#SPJ11
Related Questions
QUESTION 10 Technician A says that the automatic transmission/transaxle fluid (ATF) cooler is designed to cool the automatic transmission fluid. Technician B says that the cooler also warms the ATF when the fluid is cold. Which technician is correct
Answers
Both technicians are correct. The automatic transmission/transaxle fluid (ATF) cooler is designed to cool the automatic transmission fluid, preventing it from overheating during operation.
However, the cooler also serves another purpose - it can warm the ATF when the fluid is cold, improving its performance. The ATF cooler uses the engine coolant to heat the ATF, allowing it to reach the proper operating temperature more quickly. This is especially important during cold weather, as cold fluid can be thick and sluggish, leading to poor performance and potential damage to the transmission. By warming the ATF, the cooler helps to improve the efficiency and longevity of the transmission. Therefore, both technicians are correct in their statements about the function of the ATF cooler. It is important for technicians to understand the various components of the transmission system, including the ATF cooler, in order to properly diagnose and repair any issues that may arise.
Learn more about automatic transmission/transaxle fluid here-
https://brainly.com/question/29968294
#SPJ11
All of the following are part of the "state health exchanges" provision of the Patient Protection and Affordable Care Act (ACA) except:
a) Each state is required to establish an Affordable Insurance by 2014.
b) Small business with fewer that 50 employees will be exempt from being required to participate in the program.
c) Low-income individuals will be eligible for tax credits to effect the costs of buying health insurances.
d) Health insurance policies that meet certain specified requirements will be offered by state-run agencies, by non-profit firms, or by federal government.
Answers
The correct answer is b) Small business with fewer than 50 employees will be exempt from being required to participate in the program. The "state health exchanges" provision of the ACA requires each state to establish an Affordable Insurance Exchange by 2014.
These exchanges are intended to provide a marketplace where individuals and small businesses can shop for affordable health insurance plans. Low-income individuals will be eligible for tax credits to offset the costs of buying health insurance through these exchanges. Additionally, health insurance policies that meet certain specified requirements will be offered by state-run agencies, non-profit firms, or the federal government. This provision of the ACA aims to make health insurance more accessible and affordable for individuals and small businesses.
Know more about health insurance policies here:
https://brainly.com/question/29423491
#SPJ11
Use a function in the appropriate cell to determine the best manufacturing candidate based on minimum cost. Specify an exact match in your function since the values are not sorted. Use a similar formula in the appropriate cell to find the best shipping candidate based on minimum cost.
Answers
This function will return the minimum value in the range of cells A2:A6.
What is Function?Function is a self-contained block of code that is used to perform a particular task in a computer program. It is a set of instructions that can be called upon to perform a specific action. Functions are often used to break up a program into smaller, more manageable pieces that can be reused or combined with other functions to create more complex programs. Functions can also be used to simplify and shorten the length of a program, which makes it easier to read and debug. A function typically takes an input, performs a calculation or some type of action with that input, and then returns the result.
For finding the best manufacturing candidate based on minimum cost, we can use the MIN function. The MIN function returns the smallest numeric value in a set of values.
Syntax: =MIN(number1, [number2], ...)
Example: =MIN(A2:A6)
This function will return the minimum value in the range of cells A2:A6.
For finding the best shipping candidate based on minimum cost, we can use the MIN function in the same way. The syntax and example would be the same as above.
To learn more about Function
https://brainly.com/question/28321052
#SPJ1
Americans spent approximately __ cents of each dollar on the purchase of energy?
Answers
Answer:
14 cents
Explanation:
1 trillion US dollar
q5: the chord length of the f-22 where the wing joins the center body is 21.5 ft. consider the airplane making a high-speed pass at a velocity of 1398 ft/s at sea level (mach 1.2). calculate the reynolds number at the wing root. (round the final answer to two decimal places.)
Answers
The chord length of the F-22 where the wing joins the center body is 21.5 ft.
If the airplane is making a high-speed pass at a velocity of 1398 ft/s at sea level (Mach 1.2),
the Reynolds number at the wing root can be calculated as follows:
The formula for calculating the Reynolds number is given by:
Re = rho * v * c / µ
where,
ρ = Density of air (at sea level) = 1.225 kg/m
3v = Velocity of aircraft = 1398 ft/s
c = Chord length of wing = 21.5 f
t = 6.5532
µ = Dynamic viscosity of air (at sea level) = 1.789 * 10^-5 Pa s (approx.)
We need to convert the values to S.I. units before we can apply them in the formula.
Rho = 1.225 kg/m
3v = 427.2 m/s
c = 6.5532 ft = 1.997 mµ = 1.789 * 10^-5 Pa s
Now we can substitute the values in the formula and simplify as follows:
Re = rho * v * c / µ= (1.225 kg/m3) * (427.2 m/s) * (1.997 m) / (1.789 * 10^-5 Pa s)= 1.015 * 10^7
This is the Reynolds number at the wing root. Rounding off to two decimal places gives a final answer of 10,150,000.
the Reynolds number at the wing root is 10,150,000.
To know more about joins visit:
https://brainly.com/question/32156848
#SPJ11
The inner and outer surfaces of a 0.5-cm thick 2-m x 2-m window glass in winter are 10°C and 3°C, respectively. If the thermal conductivity of the glass is 0.78 W/m-K, determine: i. the amount of heat loss through the glass over a period of 5 h. ii. What would your answer be if the glass were 1 cm thick?
Answers
The amount of heat loss through the glass over a period of 5 hours is 55710 Joules.
Given values
Thickness of the window glass, t = 0.5 cm = 0.005 m
Area of the window glass, A = 2 m x 2 m = 4 m²
Thermal conductivity of the glass, k = 0.78 W/m-K
Temperature of inner surface, T₁ = 10°C
Temperature of outer surface, T₂ = 3°C
Time, t = 5 hours
The rate of heat transfer is given byQ/Δt = (kA/ t) × (T₁ - T₂)
Substituting the values, we getQ/5 = (0.78 × 4 × 100)/(0.005 × 7) × (10 - 3)Q/5 = 8928.57Q = 8928.57 × 5Q = 44642.85 Joules
The amount of heat loss through the glass over a period of 5 hours is 44642.85 Joules.
Now, the thickness of the window glass is 1 cm = 0.01 m
The rate of heat transfer is given byQ/Δt = (kA/ t) × (T₁ - T₂)
Substituting the given values, we getQ/5 = (0.78 × 4 × 100)/(0.01 × 7) × (10 - 3)Q/5 = 11142Q = 11142 × 5Q = 55710 Joules
Therefore, if the thickness of the window glass is 1 cm, the amount of heat loss through the glass over a period of 5 hours is 55710 Joules.
Know more about the Thermal conductivity
https://brainly.com/question/14523878
#SPJ11
which of the following is a function of a safety device
Answers
Answer:
what are the options available?
Read the following paragraph as quickly as you can, and see if you encounter any diculties.
Aoccdrnig to rscheearch at an Elingsh uinervtisy, it deosn't mttaer in waht oredr the ltteers in a wrod are, the olny iprmoetnt tihng is taht the frist and lsat ltteer is at the rghit pclae. The rset can be a toatl mses and you can sitll raed it wouthit a porbelm. Tihs is bcuseae we do not raed ervey lteter by itslef but the wrod as a wlohe.
This has been presented as an example of a principle of human reading compre-hension. If you keep the rst letter and the last letter of a word in their correct positions, then scramble the letters in between, the word is still quite readable in the context of an accompanying paragraph. However, it seems that this is a bit of a myth and not truly based on solid research.1 In short, for longer words the task is much more dicult. Nonetheless, we are going to imitate the process on some English text.
The task will be to read in a paragraph from a le, scramble the internal letters of each word, and then write the result to a le. Handling punctuation is tricky. You are required to deal with punctuation that comes at the end of a word (period, question mark, exclamation, etc.)|that is, punctuation is left untouched and does not count as the nal unscrambled letter. Optionally, one can deal with the more dicult task of handling all punctuation, such as apostrophes for possessives or hyphenated words. Truly randomizing the order of letters is a task for later in the text, but we can do some reasonable approximations now. Attacking this problem in a divide-and-conquer way should begin by writing code to scramble the letters in a word.
Create a dierent solution by dening scrambling functions for each of the following approaches: (Each approach counts as a dierent problem)
(a) For each letter choose a random number and rotate that letter by the random amount. Import random and use the random.randint(a,b) function where `a' and `b' dene the range of random numbers returned.
(b) Implement a dierent method to scrambling the letters. You must clearly describe in the comments the process to scramble the letters in place.It must be dierent than the process from part a.
Answers
Answer:
a
Explanation:
just took the quiz
What is the aim of reviewing a research paper?
Answers
Answer:
Purpose of review papers
They carefully identify and synthesize relevant literature to evaluate a specific research question, substantive domain, theoretical approach, or methodology and thereby provide readers with a state-of-the-art understanding of the research topic.
A new flexible fuel vehicle is traveling at 75 mph on I-10 in Arizona. The vehicle has a mass of 2857 ibm. Determine its kinetic energy in kJ
Answers
Answer:80 kj
Explanation:The kinetic energy of a moving body is given by,
Here, m is mass of the body, v is its velocity.
Given, m= 1600-kg and v = 10 m/s.
Substituting these values in above equation, we get
In kilojoules,
When your workplace obtains new materials, you should add them to the chemical list:
Answers
Answer:
immediately
Explanation:
The primary energy source for the controller in a typical control system is either brainlythe primary energy source for the controller in a typical control system is either
Answers
Answer:
a pneumatic or electric power
Explanation:
The primary energy source for the controller in a typical control system is either "a pneumatic or electric power."
This is because a typical control system has majorly four elements which include the following:
1. Sensor: this calculates the controlled variable
2. Controller: this receives and process inputs from the sensor to the controlled device as output
3. Controlled device: this tweak the controlled variable
4. Source of energy: this is the energy used to power the control system. It could be a pneumatic or electric power
a) Sketch a typical GSM TDMA frame. b) What are the functions of the Tail bits, stealing bits, Training sequence, and the guard bits. c) Enumerate all the possible scenarios by which the data bits in a frame can be used.
Answers
1) the sketch of thetypical GSM TDMA frame is attached accordingly.
2) a) Tail bits - Provide synchronization and signal recovery in frame transmission.
b) Stealing bits - Control purposes by taking bits from payload data.
c) Training sequence - Predefined patterns for channel estimation and synchronization.
d) Guard bits - Reduce interference and fading effects in communication channels.
e) Data bits scenarios - Transmit user data, control info, error correction codes, etc.
What is the explanation for the above?a) Tail bits - Tail bits are used indigital communications to ensure proper synchronization and signal recovery by providing a known pattern at the end of a frame.
b) Stealing bits - Stealing bits are used in certain encoding schemes to steal bits from the payload for control purposes, such as error detection or channel coding.
c) Training sequence - Training sequences are predefined patterns inserted in a data frame tofacilitate channel estimation, equalization, or synchronization in communication systems.
d) Guard bits - Guard bits, also known as guard intervals, are inserted between symbols or frames to mitigate the effects of inter-symbol interference or multipath fading in communication channels.
e) Possible scenarios for data bits usage - Data bits in a frame can be used for various purposes, including transmitting user data, control information, error correction codes,synchronization markers, addressing, or any other relevant information needed for the specific communication protocol or application.
Learn more about TDMA Frame at:
https://brainly.com/question/33364186
#SPJ4
Which unit is used, when specifying a vehicle's height, length and width?
Meters
Millimeters
Kilometres
Centimeters
Answers
Answer:
Centimeters
Explanation:
Fluid P is water and fluid Q is mercury. If the specific weight of mercury is 13. 6 times that of water and the atmospheric pressure at A when = 15cm and h2 = 30cm? (59. 8KN m-2)
Answers
The pressure exerted by water at point A is 4.75 kN/m^2, or 4.75 kPa.
The specific weight of mercury is 13.6 times that of water. Given that the atmospheric pressure at point A is 15 cm and the height difference between points A and B (h2 - h1) is 30 cm, we can determine the pressure difference between the two points.
The specific weight of a fluid is the weight per unit volume of the fluid. In this case, the specific weight of water is denoted by γw, and the specific weight of mercury is denoted by γm. We can express the relationship between these two specific weights as:
γm = 13.6γw
Since the specific weight of a fluid is directly proportional to the pressure it exerts, we can write:
Pm = 13.6Pw
Where Pm is the pressure exerted by mercury and Pw is the pressure exerted by water.
Using the hydrostatic pressure equation, we can relate the pressure difference to the height difference:
Pw = γw * h1
Pm = γm * h2
Substituting the values and known relationships:
Pw = γw * h1 = 13.6 * γw * h2 = 13.6 * Pw
Simplifying the equation:
12.6 * Pw = 59.8 kN/m^2
Dividing both sides by 12.6:
Pw = 4.75 kN/m^2
Therefore, the pressure exerted by water at point A is 4.75 kN/m^2, or 4.75 kPa.
Please note that there is a discrepancy between the given atmospheric pressure (59.8 kN/m^2) and the calculated pressure of water (4.75 kN/m^2). It is possible that there was an error in the provided atmospheric pressure value or in the calculations.
Learn more about pressure here
https://brainly.com/question/30117672
#SPJ11
nec 210.12(a) requires afci protection for the branch-circuit wiring that supplies all electrical outlets in specific rooms in dwellings. the branch circuits serving which areas, locations, or rooms in dwellings are not required to have afci protection?
Answers
NEC 210.12(a) mandates the use of AFCI protection for branch-circuit wiring that powers all electrical outlets in certain rooms in homes. The requirement aims to reduce electrical fires caused by arc faults in the wiring.
There are exceptions to this rule. AFCI protection is not required for branch circuits that serve areas, locations, or rooms that are not listed in NEC 210.12(a). For instance, AFCI protection is not necessary for the branch circuits that supply power to bathrooms, laundry rooms, garages, and other areas that are not habitable. Additionally, AFCI protection is not required for branch circuits that are used for specific purposes, such as those that power fire alarms, smoke detectors, or security systems. In conclusion, not all branch circuits in dwellings need AFCI protection as some are exempted based on the NEC 210.12(a) guidelines.
To know more about AFCI protection visit:
brainly.com/question/31075701
#SPJ11
Q3 (Unseen part) d) The best possible Coefficient of Performance (COP) would be that for a machine with Carnot cycle performance. What would be the maximum level of the COP for a heat pump operating between 0°C and 20°C? [2 marks] e) The British Government has announced that the installation of natural gas boilers in new build homes will be banned in 2025. Why is the Government doing this? [1 mark] f) The use of heat pumps as an alternative method to heat housing is seen as the best way forwards. What sources of heat could be used to supply the heat consumption of the heat pumps? Suggest at least two possible sources of the required low-grade heat. [2 marks] /Question continued on next page 4 H3053 THERMAL POWER CYCLES g) Where would the work come from to drive the heat pump systems? How might this decision influence the success of the Government policy? [2 marks] h) Renewable energy sources; wind, wave and solar are all intermittent in nature. If we become reliant on these sources power how can we avoid power outages? [2 marks] i) Discuss the pros and cons of heating housing with wood burning stoves. [1 mark]
Answers
The maximum COP for a heat pump operating between 0°C and 20°C is 13.65.
What is the Coefficient of Performanced) The maximum level of the Coefficient of Performance (COP) for a heat pump operating between 0°C and 20°C would be the COP of a Carnot cycle.
The COP of a Carnot heat pump formula is:
COP = Tc / (Th - Tc),
where:
Tc =the absolute temperature of the cold reservoir (0°C = 273 K)
Th = the absolute temperature of the hot reservoir (20°C = 293 K).
So putting in these values into the formula, we get:
COP = 273 K / (293 K - 273 K) = 273 K / 20 K
= 13.65.
UK Govt bans gas boilers in new homes by 2025 due to environment. Gas burning emits CO2 that causes global warming. Gov't bans natural gas boilers to cut emissions & move towards sustainable, low-carbon future. Heat pumps are a promising alternative for housing heating due to their ability to use different heat sources.
Two sources of low-grade heat for heat pumps are ground loops or heat exchangers that extract heat from the ground. Ground temp is stable year-round, reliable for low-grade heat. Air Heat: Heat pumps extract heat from low temperature air.
Learn more about Coefficient of Performance from
https://brainly.com/question/30902201
#SPJ4
Generators must be oversized when supplying ________ loads to reduce heating and voltage waveform distortion
Answers
Generators must be oversized when supplying non-linear loads to reduce heating and voltage waveform distortion.An oversized generator is an electrical generator that is larger than the anticipated electrical load.
The need for an oversized generator may arise if the original electrical load changes, if the system's future expansion is expected, or if the generator must run at low loads.Overloading a generator can result in system overloads, poor power quality, and device failures.
When a generator is oversized, its electrical power output capability is greater than the load that it will supply, and it will not be loaded to its full potential.
To know more about overloading visit :
https://brainly.com/question/13160566
#SPJ11
A proce for the production of 1,3-butadiene reult from catalytic dehydrogenation at atmopheric preure of 1-butene according to the reaction:
C4H8(g) → C4H6(g)H2(g)
To uppre ide reaction, the 1-butene feed tream i diluted with team in the ratio of 10 mole of team per mole of 1-butene. The reaction i carried out iothermally at 525°C, and at thi temperature 33% of the 1-butene i converted to 1,3-butadiene. How much heat i tranferred to the reactor per mole of entering 1-butene?
Answers
The balanced equation for the reaction is
C4H8(g) + 3H2(g) → C4H6(g) + 3H2(g)
The enthalpy change for the reaction can be calculated using the standard enthalpies of formation for 1-butene and 1,3-butadiene.
The heat transferred to the reactor per mole of entering 1-butene can be calculated by multiplying the enthalpy change for the reaction with the conversion of 1-butene to 1,3-butadiene (33%).
As the enthalpy change of the reaction is not provided, it is not possible to calculate the heat transferred to the reactor per mole of entering 1-butene.
Write torsion equation and explain the importance of each components.
Answers
1) The bar is straight and of uniform section
2) The material of the bar is has uniform properties.
3) The only loading is the applied torque which is applied normal to the axis of the bar.
4) The bar is stressed within its elastic limit.
Nomenclature
T = torque (Nm)
l = length of bar (m)
J = Polar moment of inertia.(Circular Sections) ( m^4)
J' = Polar moment of inertia.(Non circluar sections) ( m^4 )
K = Factor replacing J for non-circular sections.( m^4)
r = radial distance of point from center of section (m)
ro = radius of section OD (m)
τ = shear stress (N/m^2)
G Modulus of rigidity (N/m^2)
θ = angle of twist (radians)
You have accumulated several parking tickets while at school, but you are graduating later in the year and plan to return to your home in another jurisdiction. A friend tells you that the authorities in your home jurisdiction will never find out about the tickets when you re-register your car and apply for a new license. What should you do?
Answers
Answer:
pay off the parking tickets
Explanation:
In the scenario being described, the best thing to do would be to pay off the parking tickets. The parking tickets stay under your name, and if they are not paid in time can cause problems down the road. For starters, if they are not paid in time the amount will increase largely which will be harder to pay. If that increased amount is also not paid, then the government will suspend your licence indefinitely which can later lead to higher insurance rates.
Which of the following is an example of a tax
Answers
Answer:
A tax is a monetary payment without the right to individual consideration, which a public law imposes on all taxable persons - including both natural and legal persons - in order to generate income. This means that taxes are public-law levies that everyone must pay to cover general financial needs who meet the criteria of tax liability, whereby the generation of income should at least be an auxiliary purpose. Taxes are usually the main source of income of a modern state. Due to the financial implications for all citizens and the complex tax legislation, taxes and other charges are an ongoing political and social issue.
I dont know I asked this to
Explanation:
4. When the ESC system senses oversteer,
A) the brake at the inner rear or front wheel is applied to neutralize the oversteering
B) the brake at the outer corner rear or front wheel is applied to neutralize the oversteering
Answers
Technician A says that a mounting plate may be considered a piece of pulling hardware
Technician B says that a chain tensioner may be considered a piece of pulling hardware.
Who is right?
Answers
Answer:
technician b
Explanation:
Technician A and Technician B are saying about mounting plates. The statement of Technician B says that a chain tensioner may be considered a piece of pulling hardware. Technician B is right.
What is the mounting plate?The component of a joint, handle, or lock that attaches the hardware to a cabinet is called a mounting plate. Doors can be fastened to frames more easily with mounting plates. The part of a joint that matches to the wood is called a mounting plate. Furniture, cabinets, and doors can all use mounting plates.
A sort of mechanical tool called chain tensioner aids in preserving the ideal tension in a chain. Inanition in a chain or belt can result in noise and vibration, as well as make it difficult for the chain to engage with the correct and function properly.
Therefore, technician B is correct.
To learn more about the mounting plate, refer to the link:
https://brainly.com/question/14900098
#SPJ2
A structural member that has a straight longitudinal axis and constant cross section is best described as _______.
Answers
Can someone help with this please?
Answers
Answer:
with what
Explanation:
how to calculate the critical path
Answers
Answer:
Explanation:
The critical path is the longest path through a project network diagram, which includes all the activities that are critical to the completion of the project. In order to calculate the critical path, you will need to follow these steps:
Identify all the activities that need to be completed for the project.
Determine the duration of each activity. This can be estimated based on past experience or expert opinion, or by conducting time studies.
Create a network diagram that shows the sequence of activities and their dependencies. This can be done using software such as Microsoft Project or by drawing a diagram manually.
Identify the earliest start and finish times for each activity, based on the dependencies and durations.
Identify the latest start and finish times for each activity, based on the project deadline.
Calculate the total float or slack for each activity, which is the amount of time that an activity can be delayed without affecting the overall project completion date.
Identify the critical path, which is the longest path through the project network diagram that has zero total float or slack. This means that any delay in one of the activities on the critical path will cause a delay in the overall project completion date.
Once you have identified the critical path, you can focus your attention on managing and monitoring the activities on that path to ensure that the project stays on schedule.
Step 1: Write down the start and end time next to each activity.
The first activity has a start time of 0, and the end time is the duration of the activity.
The next activity’s start time is the end time of the previous activity, and the end time is the start time plus the duration.
Do this for all the activities.
Step 2: Look at the end time of the last activity in the sequence to determine the duration of the entire sequence.
Step 3: The sequence of activities with the longest duration is the critical path.
Using the same example above, here’s what the critical path diagram might look like:
Steps to calculate the critical path manually (infographic)
Once you have the critical path figured out, you can build the actual project schedule around it.
When was the first black or white hole discovered?
Answers
Answer:
1964
Explanation:
It was discovered in 1964 when a pair of Geiger counters were carried on board a sub-orbital rocket launched from New Mexico.
A plugged dishwasher sink with the dimensions of 2 ft × 1.5 ft × 1 ft is being filled with water from a faucet with an inner diameter of 1 in. If it takes 40 seconds to fill the sink to its rim, estimate the volumetric flow of water coming out of the faucet in ft^3/min
Answers
The estimated volumetric flow of water coming out of the faucet is 4.5 ft³/min.
How to calculate the volumeVolume of the sink = Length × Width × Height
= 2 ft × 1.5 ft × 1 ft
= 3 ft³
Since the sink is being filled to its rim, we can assume that the volume of water filled in 40 seconds is equal to the volume of the sink.
Now, let's convert the time to minutes:
40 seconds = 40/60 minutes
= 2/3 minutes (approximately)
Therefore, the volumetric flow of water coming out of the faucet is:
Volumetric flow = Volume of water filled / Time taken
= 3 ft³ / (2/3 minutes)
= 3 ft³ / (2/3) min
= 3 ft³ × (3/2) min
= 4.5 ft³/min
Learn more about volume on
https://brainly.com/question/27710307
#SPJ1
Which of the following is the proper term for associating a group policy to a set of Active Directory Domain Service (AD DS) objects?a.Grantingb.Linkingc.Connectingd.Implementing
Answers
The process of associating a group policy to a set of Active Directory Domain Service (AD DS) objects is an important aspect of managing network resources in an organization.
When a group policy is created in Active Directory, it needs to be linked to specific AD DS objects, such as users, computers, or organizational units (OU). This allows the policy to be applied to the relevant resources in the network. The process of linking a group policy to AD DS objects is also known as inheritance, as policies can be inherited by child objects within an OU.
Therefore, the proper term for associating a group policy to a set of AD DS objects is "linking". This is a crucial step in ensuring that policies are applied correctly and consistently across the network, and can help to streamline management and improve security.
To learn more about Active Directory Domain Service, visit:
https://brainly.com/question/14275381
#SPJ11