what is the range of values that the series resistance rs can have if we wish 90% or more of the small signal source signal to be coupled into the amplifier.

Answer:

D. All the above

Explanation:

A is correct. The theory of formation of concrete is based on this phenomenon of formation of voids because, a coarse aggregate aggregate on its own, contain voids. When a fine aggregate like sand is added, it occupies these voids. Further, when finely powdered cement is added to the mixture, it further occupies the voids between the sand particles.

B is correct. The bulking of sand should be taken into account when volumetric proportioning of the aggregates is adopted. Otherwise, less quantity of concrete per bag of cement will be produced, which naturally will increase the cost of concrete. This is because sand particles when left on their own, do not pack properly near each other due to sand buckling, leaving too many void spaces between the sand particles.

C is correct . The dry sand and the sand completely flooded with water have practically the same volume. This is due to the bulking of sand. When water is added to the sand, up to complete flooding, the sand particles pack near each other and the amount of bulking of sand is decreased. The addition of the volume of water, leads to a decrease in the volume of the sand due to the extra voids. These cancels out to practically leave the dry sand and the flooded sand with the same volume.

The safety technique that is recommended for this situation of moving a heavy industrial printer is to Bend at the knees when lifting.

This refers to the process of executing a task in a safe and acceptable way that does not put the user or others at risk

Hence, we can see that The safety technique that is recommended for this situation of moving a heavy industrial printer is to Bend at the knees when lifting.

This is to ensure that the person doing the lifting does not injure himself and has the proper form when lifting.

Read more about safety procedures here:

https://brainly.com/question/14367881

#SPJ1

To plot the data as strain versus time, you'll need to have the creep data for different time intervals. Since you haven't provided the data, I'll explain the process using general steps:

1. Gather the creep data for different time intervals at 400°C and a stress of 25 MPa.2. Create a table with two columns: one for time (in minutes or hours) and the other for strain.3. Plot the data points on a graph with time on the x-axis and strain on the y-axis. Connect the data points with a line.4. Identify the steady-state or minimum creep rate. This is the rate at which the strain changes over time once it reaches a constant value.
To know more about   strain versus visit:

brainly.com/question/32006951

#SPJ11

Solution :

It is given that :

Thermal coefficient = 0.0045/K

Ambient temperature, \($T_a = 25 - 40^\circ$\)

air velocity, v = 0-5 m/s

Solar radiation, \($G= 400-100 \ W/m^2$\)

\($P=50 \ W$\)

Model calculations :

Cell temperature (\($T_c$\))

\($T_c = T_a + \left(\frac{0.25}{5.7+3.8 \ v_w}\right) G$\)

where \($ v_w - v_a = $\) wind speed / air speed

∴ \($T_c = 2 \pi + \left(\frac{0.25}{5.7+3.8 \times 1}\right) \times 400$\)

   \($T_c = 35.526 ^\circ$\)

\($\Delta T = T_c -25$\)

      = 35.526 - 25

      = 10.526 K

Thermal coefficient = 0.0045 x 10.526

                                = 0.04737

Pv power = \($(1 -C_T) \times P \times \frac{G}{1000}$\)

                \($=(1 -0.04737) \times 50 \times \frac{400}{1000}$\)

                = 17.0526 W

The correct answer for the primary driving force for natural convection is buoyancy forces.

Buoyancy forces arise from density differences due to temperature variations within a fluid. When a fluid is heated, it expands, becomes less dense, and rises while the cooler and denser fluid falls, leading to a circulation pattern known as convection. In contrast, pressure forces and shear stress forces are not the primary drivers of natural convection. Surface tension forces, on the other hand, play a role in the movement of fluids in contact with solid surfaces, but are not significant enough to cause natural convection. In conclusion, the buoyancy forces caused by temperature differences are the main driving force for natural convection.

To know more about buoyancy forces visit:

brainly.com/question/13267336

#SPJ11

The largest positive number that can be represented in 13 bits for the two cases are

A) Unsigned number

\((2)^n - 1 = (2)^{13} - 1 = 8191\)

In Binary - \((1111111111111)_2\)

In decimal - \((8191)_{10}\)

In hexadecimal - \((1FFF)_{16\)

B) Signed number

\(2^n = 2^{13} = 8192\)

The range is from \((2^n-1)\)

therefore, the maximum value is \((4096)_{10}\)

In binary - \((1000000000000)_2\)

In hexadecimal - \((1000)_{16}\)

For more information on Binary numbers, visit

https://brainly.com/question/21285223

The circuit breaker may have a maximum rating of 20–25.Any breaker between the aforementioned ratings will therefore be adequate.

Motor rating will be translated from horsepower (hp) to watts (W).

Circuit breakers are typically installed for electric circuits 20% to 25% more than the circuit's Rated Current, whereas overload relays are typically installed for electric circuits 20% to 25% more than the circuit's Running Current.

Therefore, the rated current of the motor will be multiplied by 1.2 1.25 Step by Step to get the maximum capacity of the circuit breaker. Explanation:

1 horsepower is 745.7 watts, so 30 horsepower is 22371 watts.

Assuming 208V phase to phase voltage and unity power factor (cos=1)

Rated Power (watt) equals 3. V.I. cos

If 208V is the voltage from the phase to the neutral, then use the following formula:

Rated Power (watt) equals 3. V.I. cos.

62.169A is the rated current.

So,

62.169A is the rated current.

Therefore, the needed maximum rating for a circuit breaker is: 20–25 percent of the rated current = 62,17*1.2 62,17*1.25 = 74.6–77,7A

Any breaker between the aforementioned ratings will therefore be adequate.  

To learn more about Circuit breaker refer to:

https://brainly.com/question/14971898

#SPJ4

In a modern common rail diesel (DI) direct injection system, the fuel pressure is typically measured in pounds per square inch (psi). The correct answer from the given options is 26,000 psi.

The common rail system utilizes a high-pressure fuel pump to deliver fuel to a common rail, which then supplies the fuel injectors with pressurized fuel. This high pressure allows for better atomization of the fuel, resulting in improved combustion and efficiency.

The precise control of fuel pressure in a common rail system is crucial for optimal engine performance and emissions reduction. With a fuel pressure of 26,000 psi, the DI system can deliver the necessary fuel volume and pressure to ensure proper engine operation.

Learn more about injection system at

https://brainly.com/question/33552829

#SPJ11

The most likely answer is b. a theft of trade secrets. Copying ATVSafe Corporation's design without permission constitutes a violation of trade secrets.

Trade secrets refer to confidential information or knowledge that gives a business a competitive advantage. The design of the safety harness system developed by ATVSafe Corporation would likely qualify as a trade secret if they have taken reasonable measures to keep it confidential. By copying and using the design without authorization, TEW Vehicles would be unlawfully appropriating ATVSafe's valuable trade secret, which is considered a theft of trade secrets.

Trade secrets are protected under trade secret law, which is a branch of intellectual property law. To be considered a trade secret, the information must be kept confidential and provide a competitive advantage to the business. If ATVSafe Corporation has taken reasonable steps to keep their safety harness system design secret, such as implementing non-disclosure agreements or restricted access to the information, they can claim protection under trade secret laws.

TEW Vehicles' act of copying ATVSafe's design without permission would amount to misappropriation of ATVSafe's trade secret. This is because TEW Vehicles is gaining access to and using confidential information without authorization, and such actions can cause harm to ATVSafe's competitive position in the market. In such cases, ATVSafe Corporation could pursue legal action against TEW Vehicles to seek remedies for the theft of their trade secret, which may include damages and injunctions to prevent further use or disclosure of the design by TEW Vehicles.

To learn more about trade  Click Here: brainly.com/question/1578270

#SPJ11

Answer:

$Monitor

Explanation:

The command that would be used when running a test bench to monitor variables or signals ( i.e. changes in the values of specific variables and signa)

is the $Monitor command

This command is also used to monitor the varying values of signals during simulation.

In a compound microscope, there are two lenses located in different parts of the optical path to magnify the specimen and enable the viewer to observe fine details. The two lenses are the objective lens and the eyepiece lens.

The objective lens is located near the bottom of the microscope's tube and is closest to the specimen being observed. It is responsible for gathering light from the specimen and forming a magnified real image. The objective lens typically has a high magnification power and a short focal length.

The eyepiece lens, also known as the ocular lens, is located near the top of the microscope's tube and is positioned where the viewer places their eye to observe the specimen. The eyepiece lens further magnifies the real image formed by the objective lens and allows the viewer to see an enlarged virtual image. The eyepiece lens typically has a lower magnification power compared to the objective lens.

Together, the objective lens and eyepiece lens work in conjunction to provide magnification and visualization of the specimen in a compound microscope.

Learn more about compound microscope

https://brainly.com/question/1622133

#SPJ11

Answer:

  see the attachment

Explanation:

The circuit shown uses Nand and Nor gates to produce the desired logic. The input bits are numbered 0 to 2, right to left.

The logic is ...

  out = ((b2·b0)' + b1)'

  out = b2·b1'·b0

Answer:

c) can be made with a variety of surface finishes.

Explanation:

The missing options are;

When it comes to concrete work in construction, the concrete can be cast either in-situ or in form of pre-cast concrete.

Now in-situ concrete means concrete done on the construction site being built while pre cast concrete simply means concrete cast outside in a factory or yard and brought to site to mount.

These pre cast concrete could have different surface finishes as required as this is one of it's advantages over in situ because there is a lot of space and room to have the desired concrete finish.

a) are typically manufactured on site and then hoisted into place.

b) cannot be fiber-reinforced.

c) can be made with a variety of surface finishes.

d) never include insulation.

e) often are unreinforced.

The Lennard-Jones potential is used to model the interaction between particles and is given by:

V(r) = 4ε[(σ/r)^12 - (σ/r)^6]

where r is the distance between the particles,

σ is the distance at which the potential is zero,

and ε is the depth of the potential well.

This equation has two important parameters:

the minimum of the potential (at r = σ) and the optimal particle separation (at the minimum of the potential).

In order to compute the optimal particle separation,

we need to find the first derivative of the potential with respect to r and set it equal to zero:

V'(r) = 4ε[-12σ^12/r^13 + 6σ^6/r^7] = 0-12σ^12/r^13 + 6σ^6/r^7 = 0-12σ^18 + 6σ^12 = 0-6σ^12 = 0σ^12 = 0r = σ

This means that the optimal particle separation is equal to σ and the minimum of the potential is:

V(σ) = 4ε[(σ/σ)^12 - (σ/σ)^6] = -ε.

The symbolic solver in MATLAB can be used to verify this result.

The following code computes the derivative of the Lennard-Jones potential and finds the value of r where it is zero:

Syms r sigma epsilon

V = 4*epsilon*((sigma/r)^12 - (sigma/r)^6);

d V d r = diff(V, r);

solve (d V d r == 0, r)

This returns r = sigma as expected.

For the case where...I'm sorry but you have not completed your question.

You left a sentence unfinished.

Please complete it to enable me to answer your question better.

To know more about interaction visit:

https://brainly.com/question/33403251

#SPJ11

To minimize the risk of potential failure Slope stability analysis can help to minimize the risk of potential failure in your earth dam.

A slope stability analysis enables you to identify the critical slip surfaces and any adverse geological conditions that might compromise the stability of your earth dam.2. For an optimal design of the dam Slope stability analysis is crucial to ensure that your earth dam is optimally designed.

When you consider slope stability analysis, you can determine the best design of your earth dam to minimize the risk of slope failures and potential instability. Two causes of slope failures include:1. Human activities Human activities such as construction and mining can result in slope failures. This is because the earth's slope may have been altered or weakened, making it unstable and vulnerable to sliding, erosion, or collapse.

To know more about Slope stability visit:-

https://brainly.com/question/32554125

#SPJ11

Answer:

The IT function manages the entire information technology value chain within the organisation. It provides solutions with regard to the software and hardware IT infrastructure. We have a locally developed software which forms the frame work upon which our business rests.

Explanation:

hope it helps.

Answer:

Explanation:

From the given information:

The BOD of the wastewater can be determined by using the formula:

\(BOD _5 = \dfrac{DO_i-DO_f}{\dfrac{V_s}{V_b}}\)

where;

\(BOD _5 =\)biochemical oxygen demand = ???

\(DO_i=\) initial dissolved oxygen = 9 mg/L

\(DO_f=\) final dissolved oxygen = 4 mg/L

\(V_b =\) sample of the bottle, which is normally 300 mL

\(V_s\) = sample volume = 30 mL

\(BOD _5 = \dfrac{9-4}{\dfrac{30}{300}}\)

\(BOD _5 = \dfrac{5}{\dfrac{1}{10}}\)

\(BOD _5 = 5\times{\dfrac{10}{1}}\)

\(\mathbf{BOD _5 = 50 \ mg/L}\)

The ultimate Carbonaceous BOD is estimated from the formula:

\(y_t = L_o-L_t \\ \\ y_t = L_o-L_oe^{-kt} \\ \\ y_t = L_o (1-e^{-kt})\)

Making \(L_o\) the subject, we have:

\(L_o = \dfrac{y_t}{(1-e^{-kt}} \\ \\ L_o = \dfrac{50}{1 - e^{-0.25*5}}\)

\(L_o\) = 70 mg/L

c) The BOD left over after five days = \(L_oe^{-kt}\)

= \(70 \times e^{-0.25 *5}\)

= 20 mg/L

d) The reaction constant rate is estimated as follows:

Recall that:

\(\mathbf{BOD _5 = 50 \ mg/L}\)

Since DO measure 2 mg/L;

After 30 days, \(BOD_{30} = (9-2) \times 10 = 70 \ mg/L\)

Therefore, the reaction rate constant is:

\(\dfrac{50 \ mg/L}{70 \ mg/L} =\dfrac{1-e^{-k*5}}{1-e^{-k*30}} \\ \\ 50 (1-e^{-k*30}) = 70 (1-e^{-k*5}) \\ \\ K = 0.25 /day\)

1. Total Social Security benefits without the time value of money considered at 85 years of age:Plan A: Early Retirement at 62Brad will receive $168,000 ($1,400/month * 12 months/year * 10 years)Sheryl will receive $168,000 ($1,400/month * 12 months/year * 10 years)Total $336,000

Plan B: Full Retirement at 67Brad will receive $216,000 ($2,000/month * 12 months/year * 9 years)Sheryl will receive $216,000 ($2,000/month * 12 months/year * 9 years)Total $432,000Plan C: Late Retirement at 70Brad will receive $297,600 ($2,480/month * 12 months/year * 5 years)Sheryl will receive $297,600 ($2,480/month * 12 months/year * 5 years)Total $595,200Plan D: Combined StrategyBrad will receive $216,000 ($2,000/month * 12 months/year * 9 years)Sheryl will receive $117,600 ($1,000/month * 12 months/year * 9 years) plusBrad will receive $357,840 ($2,480/month * 12 months/year * 8 years)Total $691,4402. Future worth at 6% per year of each plan at age 85:Plan A: $336,000Plan B: $432,000Plan C: $595,200Plan D: $691,4403

. Economically, the best combination of plans for Brad and Sheryl, assuming they both live to be 85 years old is Plan D (Combined Strategy) as it provides the highest total benefit of $691,440.4. Develop at least one additional question that you think Sheryl and Brad may have. Answer the question.The couple may want to know how Social Security benefits will be taxed and if they should delay withdrawing them to avoid or minimize taxes on their benefits. The taxation of Social Security benefits is dependent on the couple’s income. If the total income (which includes 50% of Social Security benefits) is more than $32,000 for couples filing jointly.

To know more about Security visit:

https://brainly.com/question/32133916

#SPJ11

The term that refers to agreement as to what type of information the language is conveying is "semantic".

Semantic refers to the study of meaning in language, specifically the meaning of words, phrases, and sentences. It focuses on understanding how language conveys information and the relationship between words and their meanings.

For example, consider the sentence "The cat is on the mat." In a semantic analysis, we would examine the meanings of the words "cat," "on," and "mat" to understand the message being conveyed. We would determine that the sentence is expressing the location of the cat on the mat.

In contrast, the other options mentioned in the question have different meanings:

- Syntactic refers to the study of sentence structure and how words are combined to form grammatically correct sentences. It does not specifically focus on the meaning of the words.

- Logical refers to the study of reasoning and how statements relate to each other in a logical manner. It is concerned with the validity and soundness of arguments, rather than the specific meaning of words.

- Lexical refers to the study of words and their meanings. It examines the vocabulary of a language and how words are used to convey meaning. While lexical analysis is related to semantic analysis, it is not specifically concerned with the agreement of the type of information being conveyed.

Therefore, in this context, the correct term that refers to agreement as to what type of information the language is conveying is "semantic".

Learn more about semantic here :-

https://brainly.com/question/31602227

#SPJ11

It is to be noted that all UHRS platforms are optimized for the popular kinds of internet browser applications.

The Universal Human Relevance System (UHRS) is a crowdsourcing platform that allows for data labeling for a variety of AI application situations.

Vendor partners link people referred to as "judges" to offer data labeling at scale for us. All UHRS judges are bound by an NDA, ensuring that data is kept protected.

A browser is a software tool that allows you to see and interact with all of the knowledgeon the World Wide Web. Web sites, movies, and photos are all examples of this.

Learn more about internet browser applications.:
https://brainly.com/question/16829947
#SPJ1

A bug travels in the coordinate plane, moving only along lines parallel to the x-axis or y-axis.

Points A and B have coordinates (3, 2), and the bug must travel a path of length at most 20 units. To find the number of integer coordinates lying on at least one of these paths, consider the bug's maximum range. With a 20-unit limit, it can travel up to 10 units in each direction from the starting point (3, 2).

Therefore, there are 21 integer coordinates along the x-axis (10 left, 10 right, and the starting point) and 21 integer coordinates along the y-axis (10 up, 10 down, and the starting point), for a total of 42 integer points. Note that the starting point is counted twice, so the actual total is 41 integer coordinates.

learn more about coordinate plane here:

https://brainly.com/question/28471473

#SPJ11

The "col-sm-4" and "col-sm-7" classes are the ones that make two columns display on different rows.

In Bootstrap, the grid system is designed to be responsive, allowing you to control the layout of your content on various screen sizes. The grid is divided into 12 columns, and you can define how many columns an element should span using specific classes.

In your case, the combination that makes two columns display on different rows is "col-sm-4" and "col-sm-7". The explanation is that when you add the numbers in the class names (4 and 7), the sum exceeds 12, which is the maximum number of columns in the grid. This forces the second column to be displayed on a new row.

In the other options provided, the sums of the column numbers do not exceed 12, so the columns will be displayed side-by-side in a single row (col-sm-6 and col-sm-6 equal 12, col-sm-7 and col-sm-5 equal 12, and col-sm-8 and col-sm-5 equal 13 but the last column would wrap to a new row).

To know more about classes visit:

brainly.com/question/27462289

#SPJ11

The following are consequences of burning coal for energy increased levels of CO2 in the atmosphere, increased heavy metals (lead and mercury) released into the air and Acidified rain. The correct options are a, b and c.

Burning coal produces a number of main emissions: Sulphur dioxide (SO2), which causes respiratory conditions and acid rain, Nitrogen oxides (NOx), which cause respiratory diseases and smog, Particulates that cause lung sickness, respiratory diseases, fog, and haze, The main greenhouse gas produced by burning fossil fuels (coal, oil, and natural gas) is carbon dioxide (CO2).

Mercury and other heavy metals have been associated with developmental and neurological harm in both humans and other animals. Power stations produce bottom ash and fly ash as byproducts of burning coal.

Learn more about coal, here:

https://brainly.com/question/12981477

#SPJ4

The question is incomplete! Complete question along with answer and step by step explanation is provided below.

Question:

In the given circuit, V(t)=12cos(2000t+45)V, R1=R2=2Ω, L1=L2=L3=3mH and C1=250μF. You are required to find the Thevenin equivalent of this circuit using phasors.

a. If you write the Thevenin voltage, Vth, in phasor form, what is the magnitude of this phasor? Put your answer in the box below without units.

b. What is the value of the angle associated with the phasor Vth, in degrees?

c. Now, calculate the Thevenin impedance, Zth. What is the magnitude of this phasor?

d. What is the angle associated with the phasor Zth, in degrees?

Answer:

Vth = 6 < 45° V

Zth = 1.414 < 45°

a. The magnitude of the Thevenin voltage is 6 V

b. The phase angle of the Thevenin voltage is 45°

c. The magnitude of the Thevenin impedance is 1.414 V

d. The phase angle of the Thevenin impedance is 45°

Explanation:

The given voltage is

V(t)=12cos(2000t+45)

In phasor form,

V(t) = 12 < 45° V

So the magnitude of voltage is 12 V and the phase angle is 45°

Also the frequency ω = 2000

then the inductance is

L₁ = L₂ = L₃ = jωL = j×2000×0.003 = j6 Ω

and the capacitance is

C₁ = 1/jωC = 1/(j×2000×250x10⁻⁶) = -j2 Ω

and the resistance is

R₁ = R₂ = 2 Ω

Thevenin voltage:

The Thevenin voltage is the voltage that appears across the open-circuited terminals a-b (after removing L₃)

The Thevenin voltage is given by

Vth = V(t) × [ (R₂ + L₂) / (R₁ + L₁) + (R₂ + L₂) ]

Please note that there is no current flow in the capacitor due to open-circuited terminal a-b

Vth = 12 < 45°  × [ (2 + j6) / (2 + j6) + (2 + j6) ]

Vth = 12 < 45°  × [ (2 + j6) / (4 + j12) ]

Vth = 4.24264 + j4.24264 V

In phasor form,

Vth = 6 < 45° V

a. The magnitude of the Thevenin voltage is 6 V

b. The phase angle of the Thevenin voltage is 45°

Thevenin Impedance:

The Thevenin Impedance is the impedance of the circuit calculated when looking from the terminal a-b

Zth = [ (R₁ + L₁) × (R₂ + L₂) / (R₁ + L₁) + (R₂ + L₂) ] + (-j2)

Zth = [ (2 + j6) × (2 + j6) / (2 + j6) + (2 + j6) ] - j2

Zth = [ (2 + j6) × (2 + j6) / (2 + j6) + (2 + j6) ] - j2

Zth = [ (-32 + j24) / (4 + j12) ] -j2

Zth = [ (1 +j3) ] - j2

Zth = 1 + j Ω

In phasor form,

Zth = 1.414 < 45°

c. The magnitude of the Thevenin impedance is 1.414 V

d. The phase angle of the Thevenin impedance is 45°

At 1.2mpa pressure and 50c

What is pressure?
By pressing a knife against some fruit, one can see a straightforward illustration of pressure. The surface won't be cut if you press the flat part of the knife against the fruit. The force is dispersed over a wide area (low pressure).

a)Mass flow rate of the refrigerant
Therefore h1= condenser inlet enthalpy =278.28KJ/Kg
saturation temperature at 1.2mpa is 46.29C
Therefore the temperature of the condenser

T2 = 46.29C - 5
T2 = 41.29C

Now,
d)power consumed by compressor W = 3.3KW
Q4 = QL + w = Q4
QL = mR(h1-h2)-W
= 0.0498 x (278.26 - 110.19)-3.3
=5.074KW
Hence refrigerator load is 5.74Kg

(COP)r = 238/53
(Cop) = 4.490

Therefore the above values are the (a) mass flow rate of the refrigerant, b) the refrigerant load, c) the cop, and d) the minimum power input to the compressor for the same refrigeration load.

To learn more about pressure
https://brainly.com/question/13717268
#SPJ4

Answer:

True

Explanation:

Principles of plasma arc cutting, Uses a constricting nozzle to create, concentrate,  and direct the high-velocity plasma. Plasma gas is always used

in plasma arc cutting When shielding gas is also used, the process is called dual flow plasma arc cutting. I hope this helps.

The military action that involves the use of electromagnetic and directed energy is defined as Electronic Warfare (EW).

Electronic Warfare (EW) refers to military action that uses electromagnetic energy to determine, exploit, impede, or sabotage hostile use of the electromagnetic spectrum and direct energy to deny adversaries the ability to operate effectively.

It involves a wide range of military operations, including electronic intelligence collection, electronic jamming, radar jamming, infrared countermeasures, and high-powered microwave weapons. It may also include cyber warfare, which is the utilization of digital technology to conduct military operations or gain a tactical advantage.

Learn more about electromagnetic at

https://brainly.com/question/11762902

#SPJ11

Answer:

Explanation:

I do not have access to your diagram but based on what I know, a food web cannot sustain itself without decomposers. They are the main guys who break down dead animals, plants into organic or inorganic nutrients which are needed by the primary producers to grow. So if decomposers are not there then producers cannot produce and thus herbivores cannot live and carnovers die out as well. Hope this makes sense.

Check out: https://www.nationalgeographic.org/encyclopedia/decomposers/

A food web cannot sustain itself without decomposers. They are the main components who break down dead animals, plants into organic or inorganic nutrients which are needed by the primary producers to grow.

Decomposers are living organisms like fungi and bacteria. These decomposers are heterotrophic which means they must take the nutrients and it cannot make its own food. Decomposers play an eminent role in an ecosystem because of their process of nutrition.

They break down the dead plants and the animals. These break down the waste of the organisms. They are very eminent for all the ecosystem. If these were not in the ecosystem, the plants cannot get essential nutrients, dead matter and waste would deposit. So the nutrients in them gets recycled back so that they can be used again.

When fish dies, there is nothing which is ingested and the bladder air starts to release, which causes the fish to sink to the bottom. After few days, the internal organs of the dead fish gets decomposed, after which a gas is formed.

Therefore, A food web cannot sustain itself without decomposers.

To learn more about decomposers on:

brainly.com/question/11165300

#SPJ2