exceeding the dielectric strength of a capacitor means you have applied too high a voltage, and probably destroyed the capacitor.

Increasing the number of grains or reducing the grain size of a metallic material causes grain-size reduction strengthening.

When the grain size of a metallic material is reduced, the number of grain boundaries increases. These grain boundaries act as barriers to dislocation movement, leading to an increase in the material's strength. This phenomenon is called grain-size reduction strengthening.

Additionally, reducing the grain size of a material can improve its ductility and toughness. This is because smaller grains require less energy for deformation and can absorb more energy before failure. However, there is a limit to how much grain-size reduction can improve a material's properties, as it can lead to increased brittleness and reduced fatigue resistance.

Therefore, finding the optimum grain size for a specific application is crucial to achieving the desired mechanical properties.

Learn more about ductility here:

https://brainly.com/question/22212347

#SPJ11

Answer:

Vgr = 0.122 = 12.2 vol %

Explanation:

Density of ferrite = 7.9 g/cm^3

Density of graphite = 2.3 g/cm^3

compute the volume percent of graphite

for a 3.9 wt% cast Iron

W∝ =  (100 - 3.9) / ( 100 -0 ) = 0.961

Wgr = ( 3.9 - 0 ) / ( 100 - 0 ) = 0.039

Next convert the weight fraction to volume fraction using the equation attached below

Vgr = 0.122 = 12.2 vol %

Answer:

Constante de resorte = 1.1 N/m

Explanation:

Dados los siguientes datos;

Fuerza = 50N

Extensión = 60cm - 15cm = 45cm

Para encontrar la constante del resorte;

Matemáticamente, la fuerza ejercida para estirar un resorte viene dada por la fórmula;

Fuerza = constante de resorte * extensión

Sustituyendo en la fórmula, tenemos;

50 = constante de resorte * 45

Constante de resorte = 50/45

Constante de resorte = 1.1 N/m

Answer:

1. Drawing grid.

2. Orthogonal.

3. Geometries.

4. CTRL+N.

5. Thirteen (13).

Explanation:

CAD is an acronym for computer aided design and it is typically used for designing the graphical representation of a building plan. An example of a computer aided design (CAD) software is AutoCAD.

Some of the features of an AutoCAD software are;

1. Drawing grid: is a regular pattern of dots displayed on the screen of an AutoCAD software, which acts as a visual aid and it's also used to define the extent of a drawing.

2. Ortho is short or an abbreviation for orthogonal, which means either vertical or horizontal.

3. Tangent is a point where two geometries meet at just a single point.

4. If you want to create a new drawing, simply press CTRL+N for the short cut key.

5. There are thirteen object snaps (Osnap) that can help you perform your task on AutoCAD easily. The 13 object snaps (Osnap) are; Endpoint, Midpoint, Apparent intersect, Intersection, Quadrant, Extension, Tangent, Center, Insert, Perpendicular, Node, Parallel, and Nearest.

Answer:

Use a non digital multimeter.

Explanation:

If a digital multimeter displays "000" when reading amperage, the technician should adjust the multimeter to a higher amperage range.

This is because "000" typically indicates that the current being measured is too low for the current range selected on the multimeter.

By switching to a higher amperage range, the technician can get a more accurate reading and ensure that the multimeter is properly measuring the current in the circuit under test.

Learn more about digital multimeter at:

https://brainly.com/question/29512413

#SPJ3

9514 1404 393

Answer:

  1

Explanation:

Only one such circle can be drawn. The diameter of the 10" circle will be a radius of the semicircle. In order for the 10" circle to be wholly contained, the flat side of the semicircle must be tangent to the 10" circle. There is only one position in the figure where that can happen. (see attached).

Answer:

a. The content of a ROM (.mif file) is first stored in memory. The memory address is then fed to the ROM and is decoded to select a specific memory location.

The content of that memory location (which is a word in the .mif file) is then output as a digital signal. This digital signal is passed through a digital-to-analog converter (DAC) to convert it to an analog signal. This analog signal is then passed through a low-pass filter to remove any high-frequency noise and to smooth out the signal, resulting in a continuous synthesized waveform.

b. Multiplying and dividing by powers of 2 using bit shifting is a process commonly used in digital systems. To multiply a number by a power of 2, you simply shift the binary representation of the number to the left by the number of bits that corresponds to the power of 2. For example, to multiply the number 5 by 4 (which is 2 to the power of 2), you would shift the binary representation of 5 (which is 101) to the left by 2 bits, resulting in 10100, which is the binary representation of 20.

To divide a number by a power of 2, you simply shift the binary representation of the number to the right by the number of bits that corresponds to the power of 2. For unsigned numbers, the empty bit positions that are created by the shift are filled with 0s. For example, to divide the number 20 by 4 (which is 2 to the power of 2), you would shift the binary representation of 20 (which is 10100) to the right by 2 bits, resulting in 101, which is the binary representation of 5.

For signed numbers, the process is a bit more complicated due to the existence of the sign bit. When shifting a signed number to the right, you must fill the empty bit positions that are created by the shift with the sign bit. This is known as sign extension. For example, if you are dividing the number -20 by 4, you would first represent -20 in binary using two's complement notation (which is 11101100). Then, you would shift this binary representation to the right by 2 bits, resulting in 11111011, which is the binary representation of -5 after sign extension.

c. Since the .mif file has 512 words, which can be represented using 9 bits (2^9 = 512), the address bus should be 9 bits wide. Each word in the .mif file is 32 bits long, so the data bus (q bus) should be 32 bits wide. Therefore, the LPM_ROM should be set up with a 9-bit address bus and a 32-bit data bus to use this .mif file.

Learn more about ROM here:

https://brainly.com/question/15302096

#SPJ11

Answer: B) Rotating

Explanation: Osha 10 Career safe

The correct option for the implication of low variety is B) Flexibility needed. Variety refers to the number of different products, services, or activities that an organization offers. High variety means that a company offers a wide variety of products or services, while low variety means that a company provides a limited range of products or services.

One of the implications of low variety is that customers have limited options. They are restricted to purchasing only those goods and services that the company offers, which may not match their requirements or preferences. This may lead to losing customers to rivals who offer a greater variety of goods and services.

In the case of low variety, it is critical to have the required flexibility. Customers may ask for certain specific goods or services that are not provided by the company. To meet customer requirements, the company should be adaptable and able to rapidly respond to customer requests by expanding its product line. As a result, low variety necessitates the need for flexibility.

The other given options are not valid. Low unit cost is not related to low variety. Unit cost may be affected by economies of scale and other factors, but it is not directly related to variety. High complexity is not related to low variety as well. As the range of goods and services offered by the company increases, the complexity of the company's operations and management also increases. Matching customers' specific needs is partially correct because the company cannot match customer specific needs in low variety. In low variety, the company has a limited range of goods and services, so it is not possible to fulfill all the customers’ specific needs.

Know more about implication of low variety  here:

https://brainly.com/question/32400070

#SPJ11

Answer:

"Physical" would be the right approach.

Explanation:

So the answer here is just the perfect one.

A POTW is being designed to treat 2.5 MGD. The volume of the grit chamber is approximately 78,100 gallons.

The grit chamber is designed to remove and separate the solids of a higher density, such as sand, silt, and gravel, from the sewage water. The grit chamber’s volume is estimated based on the sewage flow rate (Q) and the detention time (t) required for settling grit in the chamber.

Using the following formula for calculating the volume of the grit chamber:

V = Q x t x c

Where V is the volume of the grit chamber

Q is the sewage flow rate, which is given as 2.5 MGDt is the detention time required for settling of grit, which is taken as 45 seconds

C is the empirical constant, typically assumed to be 1.5 to 2.0

For the above problem, we can calculate the grit chamber's volume as follows:

V = 2.5 MGD x (45 s / 86400 s/day) x 1.5V = 0.0781 MG or 78,100 gallons

You can learn more about volume at: brainly.com/question/13338592

#SPJ11

A POTW or Publicly Owned Treatment Works is a treatment plant that is owned and operated by a state or local government for the purpose of treating municipal wastewater.

A grit chamber is used to remove grit, sand, and other heavy inorganic solids from wastewater before it is treated further. The grit chamber is designed to allow the heavier solids to settle to the bottom while the lighter organic materials continue on to the next stage of treatment.For designing the grit chamber, the following formula is used: Volume of grit chamber (V) = Q × T × GWhere, Q = Design flow rate (MGD)T = Detention time (min)G = Surface overflow rate (ft/min)The given design flow rate is 2.5 MGD.We need to choose an appropriate detention time and surface overflow rate. A detention time of 2-5 minutes is typical for grit chambers. A surface overflow rate of 1-3 ft/min is also typical.Let's assume a detention time of 3 minutes and a surface overflow rate of 2 ft/min.V = 2.5 × 3 × 2 = 15 cubic feetTherefore, the volume of the grit chamber required is 15 cubic feet.

To know more about wastewater visit:

https://brainly.com/question/29751879

#SPJ11

The monthly output of a certain product can be given by the function

\(`Q(x) = 2500x^(5/2)`\)

where x is the capital investment in millions of dollars.

differentiate the function Q(x) with respect to x.

\(dQ/dx = d/dx(2500x^(5/2))\)

Using the power rule of differentiation, we have:

\(dQ/dx = (5/2) * 2500 * x^(5/2 - 1)dQ/dx

= 6250x^(3/2) `dQ/dx

= 6250x^(3/2)`\)

which gives us the effect on the output if an additional capital investment of $1 million is made.

Note: To estimate the effect on the output if an additional capital investment of $1 million is made, we substitute x with x+1 in the expression for `dQ/dx`. This gives us the new output and the increase in output due to the additional investment.

To know more about function visit:

https://brainly.com/question/30721594

#SPJ11

None of the following is a preventive measure aimed at reducing motor vehicle accidents caused by poor decision-making in young drivers: driver “buddy systems”, increased penalties for violations of driving laws, or driver’s education classes.

The most effective measures to reduce motor vehicle accidents are for young drivers to be taught the rules of the road and to develop good decision-making skills. These measures include: using defensive driving techniques, limiting distractions while driving, avoiding driving while impaired, and understanding the risks of speeding or aggressive driving. Young drivers should also be taught the importance of wearing seatbelts, checking tire pressure and vehicle maintenance, and having emergency preparedness kits in their vehicles. Educating young drivers on these safety measures is essential to reduce motor vehicle accidents.

To learn more about Buddy :

https://brainly.com/question/30908546

#SPJ11

Answer:

Explanation:

It appears that you are trying to solve a problem involving an insulated rigid tank containing saturated liquid water and water vapor. To determine the volume of the tank, you will need to know the mass of the liquid water and the mass of the water vapor. The mass of the liquid water can be calculated by multiplying the mass of the water and vapor mixture by the fraction of the mixture that is liquid water (1.4 kg * 0.25 = 0.35 kg). The mass of the water vapor can be calculated by subtracting the mass of the liquid water from the total mass of the mixture (1.4 kg - 0.35 kg = 1.05 kg).

To determine the final temperature of the tank, you will need to know the amount of heat added to the tank by the electric resistor and the specific heat capacity of the water and water vapor mixture. The specific heat capacity is a measure of the amount of heat required to raise the temperature of a substance by a certain amount. The specific heat capacity of water is 4.186 J/g°C, and the specific heat capacity of water vapor is 2.080 J/g°C.

To determine the electric power rating of the resistor, you will need to know the amount of heat added to the tank by the resistor and the time over which the heat was added. The power rating of the resistor is equal to the amount of heat added to the tank divided by the time over which the heat was added.

I hope this helps clarify the problem and provide some guidance on how to solve it. If you have any further questions or need additional help, please don't hesitate to ask.

Answer:

The speed will be "3.58 ft/s". The further explanation is given below.

Explanation:

Number of knots

= 15

For the similarity of Froude number:

⇒  \(\frac{V_{m}}{\sqrt{g_{m}l_{m}} }=\frac{V}{\sqrt{gl} }\)

Here,

\(l = length\)

\(g_{m}=g\)

⇒  \(\frac{V_{m}}{V}=\sqrt{\frac{l_{m}}{l} }\)

    \(V_{m}=\sqrt{\frac{1}{50} }\times number \ of \ knots\)

         \(=\sqrt{\frac{1}{50}}\times 15\)

         \(=2.12 \ knots\)

Now,

⇒  \(1 \ knots=0.514\times 3.281\)

                 \(=1.69 \ ft/s\)

So that,

⇒  \(V_{m}=2.12\times 1.69\)

          \(=3.58 \ ft/s\)

The length is 14m and width is 10.5m when Samantha has 35 m of fencing to build a three-sided fence.

From the information given, Samantha has 35 m of fencing to build a three-sided fence around a rectangular plot of land that sits on a riverbank.

It should be noted that the area of a rectangle is calculated as:

= Length × Width

Also, the perimeter will be calculated as:

= 2(length + width)

Based on the information given, the perimeter will be:

35 = 2w + l

l = 35 - 2w

Area = Length× Width

Area = w(35 - 2w)

150 = 35w - 2w²

-2w² + 35w - 150

w = 10.5 meters

Length = 35 - 2w

= 35 - 2(10.5)

= 35 - 21

= 14

The length is 14m and width is 10.5m

Learn more about rectangles on:

brainly.com/question/27738448

#SPJ1

Answer: Most master’s degree programs will take an average of two years from start to finish – about half of the time it takes to earn your bachelor’s degree. While bachelor’s degree programs involve many introductory and general education courses, a master’s degree curriculum is all about the subject area you selected to study.

Explanation: Hope this was helpful

At 0.7V forward bias, I ≈ 3.3 mA. Holes carry most of the current due to higher doping in the n-side.

(a) The contact potential Vo can be determined using the formula Vo = (kT/q) * ln(Na * Nd / ni^2), where k is the Boltzmann constant, T is the temperature, q is the elementary charge, and ni is the intrinsic carrier concentration.

Assuming room temperature (T = 300K), Vo ≈ 0.86V.

(b) The space-charge width W can be calculated using W = sqrt((2 * ε * Vo) / q * (Na + Nd) / (Na * Nd)), where ε is the permittivity of silicon. W ≈ 6.67 x 10^-6 cm.

(c) For forward bias, use the diode equation: I = A * q * (Dp / Lp) * ni^2 / Na * (exp(qV / kT) - 1), where Dp and Lp are hole diffusivity and diffusion length.

At 0.7V forward bias, I ≈ 3.3 mA. Holes carry most of the current due to higher doping in the n-side.

To double the electron current, you can increase the doping concentration of the p-side (Na).

Read more about forward bias here:

https://brainly.com/question/31492109

#SPJ1

Answer:

Option B, qualification-based selection

Explanation:

Whenever bidding is done for seeking professional services, selection of contractor should be done using qualifications-based selection.

While seeking professional service, focus is on selecting the best quality and value matter, hence the contracting agency with best experience and skill for the job is selected.

The estimated drag force on the prototype submarine is approximately 30 N.

To estimate the drag force on the prototype submarine, we can use the concept of dynamic similarity. Dynamic similarity states that two systems will experience similar forces when their Reynolds numbers are the same. The Reynolds number (Re) is a dimensionless parameter that describes the ratio of inertial forces to viscous forces in a fluid flow.

Since the model is one-fifth scale, the length of the model submarine would be 4.85 m / 5 = 0.97 m. The speed of the model submarine in the wind tunnel is not given, but we know the speed of the prototype submarine in water. To maintain dynamic similarity, we need to scale the speed as well. Therefore, the speed of the model submarine can be calculated as 0.440 m/s / 5 = 0.088 m/s.

The kinematic viscosity of air is given as u = 1.849 x 10^-5 kg/m-s, and the air density is p = 1.184 kg/m^3. Thus, the Reynolds number of the model submarine in the wind tunnel can be calculated as:

Re_model = (p_air * v_model * L_model) / u_air

        = (1.184 kg/m^3 * 0.088 m/s * 0.97 m) / (1.849 x 10^-5 kg/m-s)

        ≈ 58,518

The Reynolds number of the prototype submarine can be calculated using the same equation, but with the properties of water and the dimensions of the prototype submarine:

Re_prototype = (p_water * v_prototype * L_prototype) / u_water

            = (999.1 kg/m^3 * 0.440 m/s * 4.85 m) / (1.138 x 10^-3 kg/m-s)

            ≈ 1,634,635

Since the model submarine and the prototype submarine need to have the same Reynolds number for dynamic similarity, we can set the Reynolds numbers equal to each other and solve for the drag force on the prototype submarine:

Re_model = Re_prototype

58,518 = (D_model * v_model * L_model) / u_air

Solving for D_model, we get:

D_model = (58,518 * u_air * L_model) / v_model

Now, we can substitute the values and calculate the drag force on the prototype submarine:

D_prototype = (58,518 * u_air * L_prototype) / v_model

           = (58,518 * 1.849 x 10^-5 kg/m-s * 4.85 m) / 0.088 m/s

           ≈ 30 N

Therefore, the estimated drag force on the prototype submarine is approximately 30 N.

Learn more about force:

brainly.com/question/30507236

#SPJ11

A torsion isn't part of the shock absorber. Hence, technician A is wrong and technician B is correct.

The suspension system allows the wheel to up and down over bumps in the road. The suspension system makes the wheels and tires to up and down to absorb the shock from bumps. The rubber tires and air in the tires also slow down the ride over hard surfaces and conform to slightly uneven and rough surfaces. Thus, technician B is correct. Meanwhile, the technician A is wrong because a torsion isn't kind of shock absorber.

Kind of shock absorbers are:

Learn more about shock absorbers, here https://brainly.com/question/10838031

#SPJ4

A full wave bridge rectifier is an electronic circuit that converts an alternating current (AC) signal into a direct current (DC) signal. This is done by using a rectifier transformer to convert the high-voltage AC signal.

In this scenario, the full wave bridge rectifier is being used to charge a battery of 24 volts and 120 watt-hours. The supply voltage being used to feed the rectifier is 220 volts, and a 4:1 rectifier transformer solution is being used. This means that the voltage across the secondary winding of the transformer is one-fourth of the voltage across the primary winding.

To calculate the output voltage of the rectifier, we first need to determine the voltage across the secondary winding of the transformer. Since the voltage across the primary winding is 220 volts, the voltage across the secondary winding will be 220/4 = 55 volts.

To know more about current  visit:-

https://brainly.com/question/15141911

#SPJ11

Answer:

Explanation:

A gigameter is 1,000,000,000 meters

so, let us say m is the number of meters, g is the number of gigameters

the equation then is

\(g*10^9=m\)

Answer:

0.49

0.51

Explanation:

Probability that bulb is defective :

Let :

b1 = box 1 ; b2 = box 2 ; b3 = box 3

d = defective

P(defective bulb) = (p(b1) * (d|b1)) + (p(b2) * p(d|b2)) + (p(b3) * p(d|b3))

P(defective bulb) = (1/3 * 10/20) + (1/3 * 7/15) + (1/3 * 5/10))

P(defective bulb) = 10/60 + 7/45 + 5/30

P(defective bulb) = 1/6 + 7/45 + 1/6 = 0.4888

= 0.49

P(bulb is good) = 1 - P(defective bulb) = 1 - 0.49 = 0.51

Answer:

provides the Organization with accurate data analytics ,

provides/ensures strict compliance in the organization,

helps in lowering the cost of managing data in the organization and

provides the data scientists access to the exact data they require to work with

Explanation:

The adoption of a data platform by an organization for the purpose of  handling Data, helps to simplify data governance by :

i)provides the Organization with accurate data analytics ,

ii) provides/ensures strict compliance in the organization,

iii) It helps in lowering the cost of managing data in the organization and

iv) provides the data scientists access to the exact data they require to work with

Answer:

immediately

Explanation: